YAMAHA Make Waves

MGP SeriesMixing Console

Find a Store

Can be scrolled

MGP32X A Yamaha Mixing Console MGP32X A
MGP24X A Yamaha Mixing Console MGP24X A
Outline Mixing capability Mixing channels 32 Line Inputs (24 mono and 4 stereo) 24 Line Inputs (16 mono and 4 stereo)
GROUP 4 GROUP Buses + ST Bus 4 GROUP Buses + ST Bus
AUX 6 AUX Sends + 2 FX Sends 6 AUX Sends + 2 FX Sends
MATRIX 1 Matrix out 1 Matrix out
On-board processors FX1:REV-X(8 PROGRAM, PARAMETER control)/ FX2:SPX(16 PROGRAM, PARAMETER control) FX1:REV-X(8 PROGRAM, PARAMETER control)/ FX2:SPX(16 PROGRAM, PARAMETER control)
Input channel functions Compressor CH9-24, HPF(100Hz 12dB/oct), CH EQ(MONO) ±15dB(Max.): High 8kHz shelving/ Mid 250Hz-5kHz peaking(CH1-8,13-16)/ Low 125Hz shelving, CH EQ(STEREO) ±15dB(Max.): High 8kHz shelving/ Mid 2.5kHz peaking(CH9-12)/ Low 125Hz shelving Compressor CH9-16, HPF(100Hz 12dB/oct), CH EQ(MONO) ±15dB(Max.): High 8kHz shelving/ Mid 250Hz-5kHz peaking(CH1-8,13-16)/ Low 125Hz shelving, CH EQ(STEREO) ±15dB(Max.): High 8kHz shelving/ Mid 2.5kHz peaking(CH9-12)/ Low 125Hz shelving
I/O Mic inputs MIC: 24 (INPUTS HPF: 100Hz 12dB/oct) MIC: 16 (INPUTS HPF: 100Hz 12dB/oct)
Phantom power 48V phantom power per channel 48V phantom power per channel
Line inputs LINE: 24 mono + 4 stereo, CH INSERT: 24 RETURN: 1 stereo LINE: 16 mono + 4 stereo, CH INSERT: 16 RETURN: 1 stereo
Digital I/O USB Device USB Device
General specifications Total harmonic distortion 0.02% (20Hz-20kHz@ +14dBu) 0.02% (20Hz-20kHz@ +14dBu)
Frequency response +0.5/-1.0dB 20Hz - 20kHz, refer to the nominal output level @1kHz +0.5/-1.0dB 20Hz - 20kHz, refer to the nominal output level @1kHz
Hum & noise level Equivalent input noise -128 dBu Equivalent Input Noise -128 dBu Equivalent Input Noise
Residual output noise -92 dBu Residual Output Noise -92 dBu Residual Output Noise
Crosstalk -74dB @ 1kHz -74dB @ 1kHz
Power requirements 100-240V 50Hz/60Hz 100-240V 50Hz/60Hz
Power consumption 86W max 86W max
Dimensions W 1,027mm (40.4") 819mm (32.2")
H 169mm (6.7") 169mm (6.7")
D 565mm (22.2") 565mm (22.2")
Net weight 19kg (41.9lb) 15.5kg (34.2lb)
Find Similar Products

Analog Input Specifications

Input Terminal Actual Source Impedance For Use With Nominal Input Level Connector
  PAD GAIN Sensitivity *1 Nominal Max. before clip
MONO CH INPUT
MGP32X A: 1–24
MGP24X A: 1–16		 0 -60 dB 3 kΩ 50-600 Ω Mics -80 dBu
(0.078 mV)		 -60 dBu
(0.775 mV)		 -40 dBu
(7.75 mV)		 XLR-3-31 type *2
Phone Jack *4
-16 dB -36 dBu
(12.3 mV)		 -16 dBu
(123 mV)		 +4 dBu
(1.23 V)
26 dB -34 dB 600 Ω Lines -54 dBu
(1.55 mV)		 -34 dBu
(15.5 mV)		 -14 dBu
(155 mV)		 Phone Jack *3
+10 dB -10 dBu
(245 mV)		 +10 dBu
(2.45 V)		 +30 dBu
(24.5 V)
STEREO CH INPUT
MGP32X A: 25–32
MGP24X A: 17–24		 -34 dB 10 kΩ 600 Ω Lines -54 dBu
(1.55 mV)		 -34 dBu
(15.5 mV)		 -14 dBu
(155 mV)		 Phone Jack *4
RCA Pin Jack
+10 dB -10 dBu
(245 mV)		 +10 dBu
(2.45 V)		 +30 dBu
(24.5 V)
MONO CH INSERT INPUT
MGP32X A: 1–24
MGP24X A: 1–16		 10 kΩ 600 Ω Lines -20 dBu
(77.5 mV)		 0 dBu
(0.775 V)		 +20 dBu
(7.75 V)		 Phone Jack *5
ST CH INSERT INPUT L, R 10 kΩ 600 Ω Lines -20 dBu
(77.5 mV)		 0 dBu
(0.775 V)		 +20 dBu
(7.75 V)		 Phone Jack *5
TALKBACK INPUT 10 kΩ 50-600 Ω Mics -66 dBu
(0.389 mV)		 -50 dBu
(2.45 mV)		 -30 dBu
(24.5 mV)		 XLR-3-31 type *6

0 dBu is referenced to 0.775 Vrms. 0 dBV is referenced to 1 Vrms.
*1 Sensitivity is the lowest level that will produce an output of +4 dBu (1.23 V), or the nominal output level when the unit is set to maximum level. (All faders and level controls are at maximum position.)
*2 XLR-3-31 type connectors are balanced .(1=GND, 2=HOT, 3=COLD)
*3 Phone Jacks are balanced. (Tip=HOT, Ring=COLD, Sleeve=GND)
*4 Phone Jacks are unbalanced.
*5 Phone Jacks are unbalanced.(Tip=Out, Ring=In, Sleeve=GND)
*6 XLR-3-31 type connectors is unbalanced.

Analog Output Specifications

Output Terminal Actual Source Impedance For Use With Nominal Output Level Connector
Nominal Max. before clip
ST OUT [L, R] 75 Ω 600 Ω Lines +4 dBu
(1.23 V)		 +24 dBu
(12.3 V)		 XLR3-32 type *1
Phone Jack *4
MONO OUT 75 Ω 600 Ω Lines +4 dBu
(1.23 V)		 +24 dBu
(12.3 V)		 XLR3-32 type *1
GROUP OUT (1-4) 150 Ω 10 kΩ Lines +4 dBu
(1.23 V)		 +20 dBu
(7.75 V)		 Phone Jack *2
AUX SEND (1-6) 75 Ω 600 Ω Lines +4 dBu
(1.23 V)		 +24 dBu
(12.3 V)		 XLR3-32 type *1
MATRIX OUT (1, 2) 150 Ω 10 kΩ Lines +4 dBu
(1.23 V)		 +20 dBu
(7.75 V)		 Phone Jack *2
MONO CH INSERT OUT
MGP32X A: 1–24
MGP24X A: 1–16		 75 Ω 10 kΩ Lines 0 dBu
(0.775 V)		 +20 dBu
(7.75 V)		 Phone Jack *3
ST CH INSERT OUT [L, R] 75 Ω 10 kΩ Lines 0 dBu
(0.775 V)		 +20 dBu
(7.75 V)		 Phone Jack *3
MONITOR OUT [L, R] 150 Ω 10 kΩ Lines +4 dBu
(1.23 V)		 +20 dBu
(7.75 V)		 Phone Jack *2
PHONES OUT 150 Ω 40 Ω Phones 3 mW 75 mW ST Phone Jack

0 dBu is referenced to 0.775 Vrms. 0 dBV is referenced to 1 Vrms.
*1 XLR-3-32 type connectors are balanced. (1=GND, 2=HOT, 3=COLD)
*2 Phone Jacks are impedance balanced. (Tip=HOT, Ring=COLD, Sleeve=GND)
*3 Phone Jacks are unbalanced. (Tip=Out, Ring=In, Sleeve=GND)
*4 Phone Jacks are balanced. (Tip=HOT, Ring=COLD, Sleeve=GND)

Product Category
to page top

Select Your Location